- 您现在的位置：买卖IC网 > Sheet目录470 > MAX11008EVC16 (Maxim Integrated)EVAL KIT MAX11008
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
ADC Transfer Functions
Figure 13 shows the unipolar transfer function for non-
temperature measurements, and Figure 14 shows the
bipolar transfer function used for temperature measure-
ments. Code transitions occur halfway between suc-
cessive-integer LSB values. Output coding is binary,
with 1 LSB = V REFADC /4096 for nontemperature mea-
surements, and 1 LSB = +0.125°C for temperature
measurements. All signed binary results use two’s com-
plement format.
V REFADC
ADC Conversion Scheduling
The MAX11008 ADC multiplexer scans and converts
the selected inputs in the order shown in Table 2 (see
the ADC Conversion Register (ADCCON) (Write Only)
section) when more than one channel is selected. The
results are stored in the FIFO when in ADC monitoring
mode. The BUSY signal is set at the start and reset at
the end of a scan except when the continuous convert
bit is set at which time BUSY does not then respond to
ADC conversions.
Writing a conversion command before a conversion is
complete cancels the pending conversion. Avoid
addressing the device using the serial interface while
the ADC is converting.
1111 1111 1111
1111 1111 1110
1111 1111 1101
FULL-SCALE TRANSITION
Table 2. Order of ADC Conversion Scan
1111 1111 1100
0000 0000 0011
0000 0000 0010
0000 0000 0001
1 LSB = V REFADC /4096
ORDER OF SCAN
1
2
3
4
5
6
7
DESCRIPTION OF CONVERSION
Internal device temperature
External diode 1 temperature
Output of PGA 1 for current sense
Auxiliary input 1 (ADCIN1)
External diode 2 temperature
Output of PGA 2 for current sense
Auxiliary input 2 (ADCIN2)
0000 0000 0000
0
1
2
3
INPUT VOLTAGE (LSB)
4093
4095
ADC Clock Modes
The MAX11008 offers three conversion/acquisition
modes (known as clock modes) selectable through
Figure 13. ADC Transfer Function
configuration register bits CKSEL1 and CKSEL0.
If the ADC conversion requires the internal reference
(temperature measurement or voltage measurement with
internal reference selected) and the reference has not
0111 1111 1111
0111 1111 1110
0111 1111 1101
0000 0000 0001
0000 0000 0000
1111 1111 1111
1000 0000 0010
1000 0000 0001
1 LSB = +0.125 ° C
been previously forced on (FBGON = 1), the device
inserts a typical delay of 72μs, for the reference to settle,
before commencing the ADC conversion. The reference
remains powered up while there are pending conver-
sions. If the reference is not forced on, it automatically
powers down at the end of a scan or when CONCONV in
the ADC Conversion register is set back to 0.
Internally Timed Acquisitions
and Conversions
Clock Mode 00
In clock mode 00, power-up, acquisition, conversion,
and power-down are all initiated by writing to the ADC
Conversion register and performed automatically using
1000 0000 0000
-256
0
TEMPERATURE ( ° C)
+255
the internal oscillator. This is the default clock mode.
The ADC sets the BUSY output high, powers up, and
scans all requested channels storing the results in the
Figure 14. Temperature Transfer Function
FIFO if the ADCMON bit has been set. After the scan is
______________________________________________________________________________________
25
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX11014BGTM+T
IC RF MESFET AMP 48-TQFN-EP
MAX12000ETB+T
IC AMP GPS FRONT 1575MHZ 10TDFN
MAX12005ETM+T
IC SATELLITE IF SWITCH 48-TQFN
MAX1385BUTM+
IC RF LDMOS BIAS CNTRLR 48-TQFN
MAX1470EUI+T
IC RECEIVER 315MHZ 28-TSSOP
MAX1470EVKIT-315
EVAL KIT FOR MAX1470 315MHZ
MAX1471EVKIT-315
EVAL KIT FOR MAX1471 315MHZ
MAX1472EVKIT-433#
EVAL KIT MAX1472
相关代理商/技术参数
MAX11008EVKIT+
功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
MAX1100CWG
制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1101
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA
MAX11014
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014_08
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014BGTM
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers
MAX11014BGTM+
功能描述:特殊用途放大器 Auto RF MESFET Amp Drain-Current Cntrlr RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel
MAX11014BGTM+T
功能描述:射频放大器 Auto RF MESFET Amp Drain-Current Cntrlr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel